Firefly and PC GAMESS-related discussion club

Learn how to ask questions correctly  
We are NATO-free zone

Re^8: Can't figure out how to find emission spectra of Benzene...

Pavlo Solntsev

On Tue Jun 17 '14 1:25pm, Siddheshwar Chopra wrote
>Dear Pavlo,
>I really appreciate all your help. Your guidance has helped me a lot always.
>Sir, regarding you replies:
>1) regarding state tracking... do you mean to say if i m studying singlet to singlet transition, then it is not necessary??
No.It just help you to track (watch) the state of interest if order of states changes during the geometry optimization. I believe the optimization of triplet state should be the same as singlet.

>In general can I take it as a rule of thumb to switch it on always?? Like you did..
>I just need to add - sign to activate it..and then i dont need to bother about anything else right??
It is make sense for geometry optimization only. Yes, it is safe to leave it on.

>2) I understood about using optimized coords. Of S0 for S1*.. thnx for that..
>But how did you know B3U is first excited state? I checked my o/p file with gausssum.I couldn't get that information.. i could only find A and B..
What is the point group of porphyrin? Gaussian used C2 group. It is problem with Gaussian.

>3) Regarding PCM... i checked 8.0.x manual.. but couldnt find the list of solvents.. :-(

>4) Pardon me about the last one... I am unsure about it as I read in this forum that active space is created.. yes it is not is MCSCF/XMCQDPT2...
>I just wish that the procedure you have told me will be the best suited for my needs.. :-)
>Pavlo following the same procedure, I can get singlet to either singlet or triplet transitions/emission spectra..right? But then for downward transitions, the gnd state multiplicity will change..
Probably it is correct to talk about phosphorescence. If you optimized triplet state and then looking for transition to a singlet.


>Kind Regards,
>On Mon Jun 16 '14 9:18pm, Pavlo Solntsev wrote
>>On Mon Jun 16 '14 11:00am, Siddheshwar Chopra wrote
>>>Dear Pavlo,
>>>Sorry for replying late. I just went through all the files you had provided. I am really grateful to you for taking out time to make us understand this so well. I am really thankful to you.
>>>Pavlo I checked all the files and would be glad if you could answer some basic questions:

>>>1) The emission spectra is obtained from the file "pp_opt_s1_tddft.out"?

>>>2) From S1*--> S1... How to use and understand state tracking? I actually don't understand what I am supposed to do with it. I just know how to turn it on. What happens if I switch it off?

>>In example i gave you, state tracking probably doesn't matter. However, if you want to relax say state #3 then it may be swapped with other state. In that case state tracking should be turned on. See $TDDFT ISTATE $END description.

>>>3) You said "1st excited state is B3U"...and used the same optimized coordinates of S0 while optimizing the S1*. Is it right?
>>Of course it better to start from good coordinates for excited state optimization. The best chose is ground state geometry.

>>> What should I do with the "1st excited state is B3U"?
>>Nothing. It is just first excited state of porphyrin.

>>>This step is very important for understanding. By using the optimized coords. of S0 in optimizing S1*, do you mean that the coordinates of atoms don't change in excited state?
>>No. Any geometry optimization by definition changes atomic coordinates.

>>>4) You have used PCM calculations all throughout.. They don't seem time consuming. What all solvents I could use for the same? Do I have acetonitrile available?

>>Did you check manual? There are two manual available. Th new one and old. Check both of them. CH3CN is available.
>>>Pavlo until your help, I was in this notion that I should get the most probable orbitals from UV-Vis. calculations and then optimize them for S1 and then obtain the emission spectra. But you haven't talked about most probable orbitals anywhere... Where do I apply the concept I just mentioned then?

>>Sorry, by i don't understand what you are trying to say within DFT level of theory.
>>Hope this helps.

>>>Kind Regards,
>>>On Thu Jun 12 '14 10:18am, Siddheshwar Chopra wrote
>>>>Dear Pavel,
>>>>Your suggestions have always been valuable to me. I will start working on your files and will let you know in case I need your help.

>>>>Kind Regards,

>>>>On Wed Jun 11 '14 4:17pm, Pavlo Solntsev wrote
>>>>>I attached example how to do Luminescence calculation for porphyrin molecule. For more detailed information please, check manual AND this forum.

>>>>>Salvation model has not been programmed for TDDFT+gradient. Therefore, optimization of the excited state was done without solvent correction. However, this correction was included into spectra calculation.

>>>>>Very often geometry optimization of the excited state brakes a true molecular symmetry. Keep this in mind.

>>>>>For more complex systems state of interest may be different, not S1. It is especially true if you have a donor group in your molecule and thus HOMO....HOMO-x belong to the donor, but you are looking for emission within porphyrin core. In such case you need identify the state of interest based on TDDFT(ground state) and knowledge.

>>>>>Good luck.

>>>>>On Tue Jun 10 '14 10:16pm, Siddheshwar Chopra wrote
>>>>>>Dear Alex,
>>>>>>I searched a lot on this forum regarding the same. What you told is right and I know these too. But I want to step by step how to optimize �the S1? say for �benzene.
>>>>>>And then how should I determine S0--> S1 (optimized)?
>>>>>>Please help me stepwise. Any i/p files would be of great help.. I have noted from TDDFT calc of benzene that orbitals 17-24 are most dominant ones. How do I proceed next?

>>>>>>Kind Regards,

>>>>>>n Tue Jun 10 '14 7:43pm, Alex Granovsky wrote

>>>>>>>for emission spectra you need to optimize S1 geometry and then compute
>>>>>>>vertical transition from S0 to S1 at optimized geometry of S1.

>>>>>>>Kind regards,
>>>>>>>Alex Granovsky
>>>>>>>On Sat Jun 7 '14 9:10pm, Siddheshwar Chopra wrote
>>>>>>>>Dear Firefly users,
>>>>>>>>I need some real help in determining the emission spectra (S1--->SO*) of benzene.
>>>>>>>>I have understood till optimizing the ground state and then obtaining the vertical transition from SO--->S1*...
>>>>>>>>Please help me now what I should do next? Any i/p files would be welcomed.

>>>>>>>>Kind Regards,

[ Previous ] [ Next ] [ Index ]           Tue Jun 17 '14 2:58pm
[ Reply ] [ Edit ] [ Delete ]           This message read 635 times